Jenn-Air JDB9800CWX Manual do Utilizador descarregar pdf

INSTALLATION INSTRUCTIONS

FOR CUSTOM PANEL ATTACHMENT

UNDERCOUNTER DISHWASHER

STAINLESS STEEL TUB

IMPORTANT: Before installing your dishwasher, please use this instruction sheet as a supplement to the installation instructions.

Custom Panel Models Only

Gather these additional tools and parts before starting attachment

of the custom panel. Read and follow the instructions provided in

this Instruction Sheet.

Additional Tools Needed:

³⁄₃₂" Drill bit

Additional Parts Supplied with Custom Panel Models:

Plastic studs (attached to each other by runners) (4)

Short screws (10-16 hex-head screw) (4)

Long screws (8-18 Torx

®†

head screws) (4)

Template (1) (located inside Use and Care Guide bag assembly)

Instruction sheet (1) (located inside Use and Care Guide

bag assembly)

NOTE: The screws supplied are used for only 3¾" (9.5 cm) thick

wooden panel. If the wooden panel is less than 3³⁄₈" (8.6 cm) thick,

customer must purchase screws locally.

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-422-1230. In Canada, call

1-800-807-6777.

Install Custom Panel

Follow Steps Below:

A customer supplied panel must weigh no more than 16 lbs

(7.3 kg) and must be made to specific dimensions. It is

recommended that a cabinetmaker cut the customer panel

because of the precise dimensions needed.

NOTES:

■ The handle for the custom panel is not included.

■ All mounting hardware supplied is for a ³⁄₄" (19.1 mm) thick

wood panel. If a thinner wood panel or materials other than

wood are used, it is the customer’s responsibility to obtain the

proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both sides

and all edges of the panel to avoid damage from moisture.

†®TORX, and T15 are registered trademarks of Acument Intellectual Properties, LLC.

W10750117B

1 2 3 4 5 6 ... 11 12

Resumo do Conteúdo

Página 1 - STAINLESS STEEL TUB

INSTALLATION INSTRUCTIONS FOR CUSTOM PANEL ATTACHMENTUNDERCOUNTER DISHWASHERSTAINLESS STEEL TUBIMPORTANT: Before installing your dishwasher, please us

Página 2 - Excessive Weight Hazard

101010101010Fixer les 4 goujons de plastique sur le panneau de bois avec les 4 vis courtes fournies (⁵⁄₁₆", tête hexagonale).Vérifier l'alig

Página 3

111111111111À l'aide d'un tournevis Torx® T15®, installer deux vis n° 8 x 1³⁄₈" dans les angles supérieurs pour fixer le panneau de boi

Página 4 - INSTRUCCIONES DE INSTALACIÓN

Página 5 - ADVERTENCIA

222222 Using 2 or more people, stand the dishwasher up.NOTE: Do not install kick plate until instructed to do so.Install the custom hardware handl

Página 6

333333Check custom tape alignment with metal door slots; verify tape is right-side up, and that the tape does not overhang the metal door on the top,

Página 7

444444INSTRUCCIONES DE INSTALACIÓN PARA COLOCAR EL PANEL A LA MEDIDALAVAVAJILLAS PARA INSTALARSE DEBAJO DEL MOSTRADOR TINA DE ACERO INOXIDABLEIMPORTAN

Página 8 - AVEC CUVE EN ACIER INOXYDABLE

555555Con la ayuda de dos o más personas, ponga la lavavajillas en posición vertical.NOTA: No instale la placa de protección hasta que se le indique.I

Página 9 - AVERTISSEMENT

666666Fije los 4 pernos de plástico al panel de madera utilizando los 4 tornillos cortos de cabeza hexagonal ⁵⁄₁₆" provistos.Revise que la cinta

Página 10 - 101010101010

777777Con un destornillador Torx® T15® instale los dos tornillos largos #8 x 1³⁄₈" en las esquinas superiores para asegurar el panel de madera a

Página 11 - 111111111111

888888INSTRUCTIONS D’INSTALLATION POUR LE PANNEAU PERSONNALISÉDU LAVE-VAISSELLE SOUS PLAN DE TRAVAILAVEC CUVE EN ACIER INOXYDABLEIMPORTANT : Avant d&a

Página 12 - W10750117B

999999À l'aide d'au moins deux personnes, mettre le lave-vaisselle en position verticale.REMARQUE : Ne pas installer le garde-pieds avant qu